How to setup this 1010lt-cant get the mic pres picking up? Problm photos...

[kev]

Finally got here from the states today guys! Complete with hefty import duty, ****ing 32%! whats going on...

Anyway, managed to get the outputs configd, which are sounding pretty lush indeed. I cant get the monitor (delta control panel) settings to take effect AT all. Like when i try muting and stuff it just doesnt work- same for trying to switch off left and right stuff etc. It seems to be bypassing it. God knows why! I've disabled the old sound stuff and selected the new.

Next up.. It wont even pass the test for cubase...

Its obvious that theres something i havent done here. But what

 

[Hopkins-WitchfinderGeneral]

operating system? DAW of choice? pictures aren't working?!

oh wait you said cubase, my bad.

also, you set it to monitor mix on the H/W out you're using yes?

 

[kev]

operating system? DAW of choice? pictures aren't working?!

oh wait you said cubase, my bad.

also, you set it to monitor mix on the H/W out you're using yes?

Ah... damn cantankerous web servers and software

Fixed

 

[Hopkins-WitchfinderGeneral]

wave out 1/2 volumes are at zero there, throw them up to something a bit higher

 

[Razorjack]

Argh, had this same problem the other week with a mates delta 44. It was a box that had been checked....can't remember which one though....sorry!!

 

[Hopkins-WitchfinderGeneral]

heres my settings:

monitor mix on patchbay tab Hw 1/2 out

Settings:

internal xtal
multitrack drivers: single and in sync
codec rate: 44.1 with locked and idle settings OFF!
DMA buffer: 256 samples
Asio options: disable in software monitoring checked <--- this might be the one!

 

[kev]

heres my settings:

monitor mix on patchbay tab Hw 1/2 out

Settings:

internal xtal
multitrack drivers: single and in sync
codec rate: 44.1 with locked and idle settings OFF!
DMA buffer: 256 samples
Asio options: disable in software monitoring checked <--- this might be the one!

will check!

 

[Razorjack]

Asio options: disable in software monitoring checked <--- this might be the one!

That's the one I was talking about, I'd have remembered it if I had slept in the past 2 days (damn uni work!!).

 

[Mikey Bolton]

You dont need to do an audio systems test if you are using the m-audio asio drivers. I presume you are using just asio multimedia drivers if you are running the sync tests? Also, bad luck on the import tax, I did warn you!

 

[kev]

Tried everything, but still no joy yet. The monitor mixer actually jumps up and down when i play something, so there is a signal coming in at least! Should sound be actually coming out of the speakers when playing or not? All i've actually done is install the m-audio cd that came with it. Also, tried updated drivers but i still get the same prob. Anything else i need to install? Maybe the problem lies here? Not sure which to select for the mic inputs? I've now actually got the monitor to effect out going sound, which is half the problem

 

[kev]

Break through guys- I've managed to get an audible INPUT signal working, and its sounding pretty nice! But the down side is.... its too quiet to hear, and when i say quiet, i mean the signal isnt going higher than the bottom of the green bar. Any ideas please lads? TWIGS- I hope the jumpers are set right! HAHAHAHA

 

[chadsxe]

how are you routing your moniter chain......this might be a stupid question but are you still using the stock sound card for output....

 

[chadsxe]

Break through guys- I've managed to get an audible INPUT signal working, and its sounding pretty nice! But the down side is.... its too quiet to hear, and when i say quiet, i mean the signal isnt going higher than the bottom of the green bar. Any ideas please lads? TWIGS- I hope the jumpers are set right! HAHAHAHA

Explain the input chain in detail......

 

[kev]

I think it could be sorted dude, just gonna take the PC apart, and check the jumpers. Im seriously hoping that they're set to -10 db instead of +4 db!
If not... Well it'll be back to the drawing board

 

[chadsxe]

I think it could be sorted dude, just gonna take the PC apart, and check the jumpers. Im seriously hoping that they're set to -10 db instead of +4 db!
If not... Well it'll be back to the drawing board

Try it....it only takes two seconds to switch the jumpers....

 

[kev]

Try it....it only takes two seconds to switch the jumpers....

It was the jumpers guys! Holy shit this sounds awesome now!!!! Like going to heaven or sumut!

Clips to follow!

 

[Kazrog]

This is why I own a Mac.

 

[Razorjack]

This is why I own a Mac.

Ditto! Took me 3mths to get my PC laptop set-up to happilly run a session, took me around 30mins with my iBook. :Smug:

 

[kev]

Well here's a short clip i just did, just one guitar copied a couple of times no eq or anything this is the plain sound. Its such a clear sound compared to what i had, so im well chuffd! Cant wait to try a mix. All i need now is a mesa rectifier/5150 and we'll be pumping some iron!

http://www.fireway.co.uk/den/omission/Gallery/Taunton1//clip.mp3

 

[black sugar]

Ditto! Took me 3mths to get my PC laptop set-up to happilly run a session, took me around 30mins with my iBook. :Smug:

Damn. Same hardware and software (Mac and PC versions respectively)?

FWIW, I used a Delta1010 (not LT) on a PC with Cubase SX2, SX3, and even VST over the last 3 years or so with no problems. Once I got a handle on the Delta software interface, it was smooth sailing.

Other than me generally not knowing what the fuck I was doing at first...


Dude, kev... Can you re-size those photos? By like 75% or so?